Product Reviews

SmallRig 22-Inch Magic Arm Clamp Review

A flexible overhead mounting kit for creators who want to position a phone, camera, light, or microphone at a desk or on a compatible tube.

This article contains affiliate links. We may earn a commission if you buy through them, at no extra cost to you.

The SmallRig 22 magic arm review comes down to reach, positioning flexibility, and the weight of the gear you plan to mount.

Its 22-inch arm and included phone clamp make it a practical option for overhead filming, streaming, and desk-based creative work.

SmallRig Magic Arm Review Summary

The quick verdict

SmallRig 22-Inch Magic Arm Clamp
4.3/5

1,000+ ratings

Read Amazon Reviews

SmallRig 22-Inch Magic Arm Clamp

A flexible overhead mounting kit for creators who want to position a phone, camera, light, or microphone at a desk or on a compatible tube.

  • The aluminum-alloy arm measures 56 cm (22 inches) and has a recommended load capacity of 600 g (21 oz).
  • Double-ball clamps at each joint allow the angles to be adjusted independently.
  • The included crab clamp opens up to 63.5 mm and has rotatable friction pads that open 50 mm for desktop or round-tube clamping.
  • Silicone pads and rubber rings add friction at the clamp, six ball joints, and both arm ends while helping protect contact surfaces from scratches.

Pros

  • The 22-inch reach offers useful positioning range for overhead and desk-based framing.
  • Independent double-ball joints provide flexibility for aiming a mounted device.

Consider before buying

  • A 600 g recommended load limits the kit to relatively light equipment; check the combined weight of the device and any attached accessories.
  • The long arm can increase leverage on the clamp and joints, so the maker advises shortening the arm when mounting a relatively heavy phone to reduce the chance of ball slippage.
Read the full review summary

The kit pairs a 56 cm (22-inch) aluminum-alloy arm with double-ball joints, a clamp that opens up to 63.5 mm, two 1/4-inch-20 screws, and a 1/4-inch-20 to 3/8-inch-16 adapter.

The arm’s stated recommended load is 600 g (21 oz), so it is aimed at relatively light equipment rather than a heavy camera rig.

It may suit illustrators filming overhead demonstrations, vloggers, streamers, and remote workers who need to place a phone, webcam, light, or microphone near a desk or compatible tube.

Its long reach offers room to position gear, while the phone clamp accommodates phones 5.5–8.5 cm wide. As with any extended arm, keep the payload and the arm’s leverage in mind when choosing a setup.

The buying factors

SmallRig Magic Arm Scorecard

Editorial scores reflect listed features and buyer fit; they are not laboratory measurements or customer ratings.

9/10

Reach

The 56 cm (22-inch) arm is designed to extend farther than typical gear magic arms, giving more placement flexibility for overhead setups.

8/10

Angle adjustment

Double-ball clamps at each joint allow independent angle adjustments, which can help position a device around a desk or filming area.

8/10

Mounting flexibility

The clamp can attach to regular desktops or round tubes, and the kit includes common threaded hardware and a phone clamp.

6/10

Light-gear capacity

The recommended load is 600 g (21 oz), making it a better fit for modest accessories than heavy equipment.

8/10

Contact protection

Silicone pads and rubber rings are used on clamp contact points, the six balls, and both ends of the arm to add grip and help protect surfaces.

7/10

Phone compatibility

The included phone clamp fits devices 5.5–8.5 cm wide, but buyers should check their phone’s width and overall mounted weight.

Key Features and Specifications of SmallRig Magic Arm

  • The aluminum-alloy arm measures 56 cm (22 inches) and has a recommended load capacity of 600 g (21 oz).
  • Double-ball clamps at each joint allow the angles to be adjusted independently.
  • The included crab clamp opens up to 63.5 mm and has rotatable friction pads that open 50 mm for desktop or round-tube clamping.
  • Silicone pads and rubber rings add friction at the clamp, six ball joints, and both arm ends while helping protect contact surfaces from scratches.
  • The kit includes two 1/4-inch-20 screws, a 1/4-inch-20 to 3/8-inch-16 adapter, and a phone clamp for phones 5.5–8.5 cm wide.
  • The product description lists phones, webcams, lights, action cameras, monitors, and some microphones as potential devices to mount, subject to the load limit and compatible attachment points.

Pros and Cons of SmallRig Magic Arm

Pros

  • The 22-inch reach offers useful positioning range for overhead and desk-based framing.
  • Independent double-ball joints provide flexibility for aiming a mounted device.
  • The clamp is intended for both desktops and round tubes, broadening where the arm can be attached.
  • The kit includes a phone holder and common threaded adapters, giving buyers several starting points for a lightweight setup.

Consider before buying

  • A 600 g recommended load limits the kit to relatively light equipment; check the combined weight of the device and any attached accessories.
  • The long arm can increase leverage on the clamp and joints, so the maker advises shortening the arm when mounting a relatively heavy phone to reduce the chance of ball slippage.
  • The phone clamp’s stated width range is 5.5–8.5 cm; verify your phone’s width and how it fits before relying on the included holder.

Who Should Buy SmallRig Magic Arm?

Good fit

Consider it if you want an extended arm for overhead drawing videos, tabletop demonstrations, video calls, or live streaming, and your mounted device stays within the 600 g recommendation.

The combination of a long reach and independently adjustable joints can make it easier to position a phone or light without moving the desk setup itself.

It may also suit a creator who alternates between a desktop and a compatible round tube, such as a tripod or stabilizer handle.

Before buying, check the clamp opening against the surface you plan to use, confirm that your device can attach with the included hardware or phone clamp, and plan to keep heavier loads closer to the base.

Who should skip it

Skip this setup if your intended camera or accessory combination exceeds the recommended 600 g load, or if the device needs a mounting interface that the included screws and phone clamp do not provide.

It may not be the right choice if you need a short, compact mount or want to extend a heavy device fully away from its clamp point.

For heavier phones, shorten the arm and consider whether that still gives you the framing you need.

How the SmallRig Magic Arm Fits a Creator’s Setup

Reach and framing

At 56 cm, the arm is meant to put a device farther from its support point than a short accessory arm.

That can help when a camera or phone needs to look down onto a work surface, but the reach also means the mounted load has more leverage.

A stable setup depends on the device weight, how far the arm is extended, and how firmly the clamp grips its support.

Joint adjustment

Each joint uses double-ball clamps for independent angle changes. This gives the user more than one point of adjustment when aiming a phone or accessory, which can help work around a desk layout.

The description specifically cautions that a relatively heavy phone can cause slippage if too much force bears on a single ball head, so a shorter configuration is the sensible starting point for heavier loads.

Choosing a support surface

The crab clamp opens up to 63.5 mm, and its rotatable friction pads are described as opening 50 mm. It is intended for ordinary desktops as well as round tubes.

Measure the surface where you expect to attach it and consider its shape; the stated opening dimensions are useful checks, but they do not establish compatibility with every desk edge, tripod, or handle.

Matching the mounted device

The kit includes a phone clamp for devices 5.5–8.5 cm wide, along with 1/4-inch-20 screws and a 3/8-inch adapter for other compatible equipment.

The product is described for use with several light devices, including webcams, lights, action cameras, monitors, and some microphones. Buyers should confirm both the attachment interface and the combined weight before building around it.

Alternatives to SmallRig Magic Arm

No alternative model is recommended here. Compare the reach, clamp surface, and supported load that matter to your setup before choosing another option.

Is SmallRig Magic Arm Worth It?

The SmallRig 22-Inch Magic Arm Clamp is worth considering for creators who need a long, adjustable mount for a phone or other light accessory at a desk or on a compatible tube.

Its reach, double-ball joints, and included phone clamp make it relevant to overhead filming and streaming setups.

The key tradeoff is the 600 g recommended load and the leverage created by extending the arm. Check the device weight, phone width, and support surface, and keep heavier gear closer to the clamp.

If those constraints match your setup, this kit offers a flexible way to place lightweight gear.

Your review at a glance

SmallRig 22-Inch Magic Arm Clamp
4.3/5

1,000+ ratings

Read Amazon Reviews

SmallRig 22-Inch Magic Arm Clamp

A flexible overhead mounting kit for creators who want to position a phone, camera, light, or microphone at a desk or on a compatible tube.

  • The aluminum-alloy arm measures 56 cm (22 inches) and has a recommended load capacity of 600 g (21 oz).
  • Double-ball clamps at each joint allow the angles to be adjusted independently.
  • The included crab clamp opens up to 63.5 mm and has rotatable friction pads that open 50 mm for desktop or round-tube clamping.
  • Silicone pads and rubber rings add friction at the clamp, six ball joints, and both arm ends while helping protect contact surfaces from scratches.

Written by

gunkiss.com Editorial Team

Editorial team

Independent editorial coverage of illustration & creative practice.

Amazon customer reviews

See what buyers think

Explore customer reviews, photos and available video reviews on Amazon.

SmallRig 22-Inch Magic Arm Clamp

SmallRig 22-Inch Magic Arm Clamp

A flexible overhead mounting kit for creators who want to position a phone, camera, light, or microphone at a desk or on a compatible tube.

  • The aluminum-alloy arm measures 56 cm (22 inches) and has a recommended load capacity of 600 g (21 oz).
  • Double-ball clamps at each joint allow the angles to be adjusted independently.
Check Video Reviews on Amazon