The best camera mounts depend on what you’re attaching, where it needs to sit, and whether your rig uses a clamp, shoe, cage, or 15mm rods. These picks cover flexible magic arms, monitor supports, tabletop mounting, and cage-based expansion, so match the connection points and load limits to your gear.
Quick Top Products
SmallRig 1138 Double Ball Head Super Clamp
- Clamps to rods, tubes, tables, frames, and tripods.
- Includes a 1/4-inch-20 screw and action camera adapter.
- Maximum load is 1.5 kg.
Best For: Mounting a small camera, light, or microphone to a desk, rod, or frame.
SmallRig 2732 9.8-Inch Magic Arm Clamp Kit
- Includes a 9.8-inch articulating arm and super clamp.
- Clamp jaws open from 15 mm to 54 mm.
- Uses 1/4-inch and 3/8-inch mounting threads.
Best For: Positioning a monitor, light, or microphone away from a clamp point.
SmallRig BSE2346 Cold-Shoe Monitor Mount
- Designed for 5- and 7-inch field monitors.
- Offers 360-degree swivel and up to 140-degree tilt.
- Supports monitors up to 1.2 kg.
Best For: Attaching a 5- or 7-inch field monitor to a camera’s cold shoe.
SmallRig 2059 Mini Ball Head Mounts, 2-Pack
- Includes two mini ball-head mounts.
- Attaches through a cold shoe and uses a 1/4-inch screw.
- Maximum load is 3 kg per ball head.
Best For: Adding two compact cold-shoe ball-head mounts to a camera setup.
SmallRig Super Clamp with Ballhead Magic Arm
- Jaw fits rods from 14 mm to 60 mm and surfaces up to 65 mm thick.
- Includes a removable action camera adapter.
- Maximum load is 3.5 kg.
Best For: Clamping action cameras or light accessories to larger tubes, tables, or handlebars.
SmallRig 3488 Adjustable Desk Camera Stand
- Adjusts from 19 to 39 inches high.
- C-clamp fits desks up to 1.85 inches thick.
- 1/4-inch ball head supports up to 3 kg.
Best For: Setting a camera, phone, or ring light above a desk for streaming or interviews.
SmallRig 5311 11-Inch Magic Arm Clamp
- 11-inch arm with 1/4-inch-20 screw and retractable pins.
- Clamp fits diameters from 15 to 40 mm.
- Maximum payload is 1.5 kg.
Best For: Positioning a lightweight camera or accessory on a tube, tripod leg, or table.
SmallRig 5310 7-Inch Magic Arm Clamp
- 7-inch arm with retractable locating pins and 1/4-inch-20 screw.
- Clamp fits 15–40 mm diameter supports.
- Maximum payload is 1.5 kg.
Best For: Mounting a lightweight action camera, monitor, light, or microphone close to a support point.
SmallRig 942 15mm Railblock
- Holds two 15 mm rods.
- Includes short and long 1/4-inch mounting screws.
- Spring ratchet wingnut helps in narrow rig spaces.
Best For: Adding a pair of 15mm rods to a compatible camera cage or plate.
SmallRig Magic Arm Clamp Kit with Super Clamp
- Integrated anti-deflection design joins the clamp and arm.
- Rotating friction block supports flat edges and round tubes.
- Recommended load is 1.5 kg; action camera mount included.
Best For: Attaching a small camera, monitor, or light to a flat edge or round tube.
Compact Clamp with Action Camera Adapter
SmallRig Cool Ballhead Arm Super Camera Clamp Mount Double Ball Adapter, Fence Desk Table Mount for Ronin-M for Insta360, for Gopro - 1138
SmallRig’s 1138 combines a super clamp, double ball head, and action camera adapter in one compact mount. Its clamp attaches to a rod, tube, table, frame, or tripod, while the 1/4-inch-20 screw supports a camera, monitor, light, or microphone.
The aluminum and stainless steel construction has a stated maximum load of 1.5 kg. This is a practical option when you want an adjustable position without drilling or building a larger rig.
For moving setups, use a safety rope as the product guidance recommends, and keep the attached equipment within the load limit.
Best For: Mounting a small camera, light, or microphone to a desk, rod, or frame.
| Pros | Cons |
|---|---|
|
|
Choose this mount for a compact camera or accessory that needs a flexible position on a desk, tube, or frame. Its included action camera adapter adds another connection option, while the 1.5 kg maximum load calls for care with heavier monitors or cameras.
Check that the clamping surface fits the jaws and that your device has a compatible 1/4-inch-20 connection or action camera interface. For a dedicated field monitor, a monitor-specific mount may offer a more direct fit.
Long Reach with a 9.8-Inch Articulating Arm
SMALLRIG 9.8 Inches Magic Arm Clamp Kit with 1/4" and 3/8" Threaded Holes
This SmallRig kit pairs a 9.8-inch articulating arm with a super clamp, giving you more reach than a compact ball-head clamp. The arm uses 1/4-inch screws at both ends, and the clamp includes both 1/4-inch and 3/8-inch threads.
Its jaws open from 15 mm to 54 mm, and the double ball-head design rotates through 360 degrees for angle adjustment. Rubber cushions help protect the clamped surface and accessory.
This kit suits a rig where you need to move a light or monitor away from a rod, shelf, or frame. It is not magnetic or corrosion-resistant for seawater use.
Best For: Positioning a monitor, light, or microphone away from a clamp point.
| Pros | Cons |
|---|---|
|
|
This kit fits creators who need a monitor, microphone, or light offset from a clamped support point. Its 9.8-inch length adds placement flexibility, though that reach also makes it important to stay mindful of the attached setup and how the clamp is secured.
Check the support’s diameter or thickness against the 15–54 mm jaw range, then confirm the accessory can use a 1/4-inch screw. If reach is not needed, a smaller clamp can take up less space.
Cold-Shoe Monitor Support for 5- and 7-Inch Displays
SmallRig Field Monitor Mount Holder with Cold Shoe and 1/4" Inch Screw for 5 Inch and 7 Inch Monitor, with 360 Degree Swivel and 140 Degree Tilt, Rubber Cushion, Aluminum Alloy Build - BSE2346
The BSE2346 is a dedicated monitor holder for 5- and 7-inch displays. It attaches to a camera or support system through a cold shoe and secures the monitor with a bottom 1/4-inch-20 screw.
The holder swivels 360 degrees horizontally and tilts up to 140 degrees, allowing angle changes without repositioning the camera. Rubber cushions add friction and help prevent scratches, while the CNC-machined aluminum mount supports monitors up to 1.2 kg.
This is a straightforward choice for a camera-top display, provided the shoe and monitor connections match your setup.
Best For: Attaching a 5- or 7-inch field monitor to a camera’s cold shoe.
| Pros | Cons |
|---|---|
|
|
Pick this holder when your monitor has a 1/4-inch-20 connection and your camera or rig offers a cold shoe. Its 360-degree swivel and 140-degree tilt cover useful viewing adjustments, while the 1.2 kg load limit gives a clear boundary for heavier displays.
Check your monitor’s weight and the shoe’s placement before buying. A cage-mounted ARRI-style holder may be a better fit if your setup lacks a cold shoe.
Two Adjustable Ball Heads in One Pack
SmallRig 1/4" Camera Hot Shoe Mount, Ballhead Tripod with Additional 1/4" Screw, 2pcs Pack - 2059
This two-pack provides two mini ball-head mounts for small accessories and camera positioning tasks. Each mount attaches through a cold shoe and includes a 1/4-inch screw for a monitor or another compatible device.
The ball head adjusts to a range of positions, and a wingnut locks the chosen angle. The stated maximum load is 3 kg per ball head.
This pack makes sense when a rig needs two mounting points or a spare, but check the fit of your device and shoe before buying. The product is a pair of mounts, not a single support.
Best For: Adding two compact cold-shoe ball-head mounts to a camera setup.
| Pros | Cons |
|---|---|
|
|
Choose the 2059 pack if you need two compact adjustable mounts for accessories such as a monitor. The cold-shoe base and 1/4-inch screw make the connection path clear, and each ball head has a 3 kg maximum load.
Consider whether you will use both pieces, since the pack is less suited to someone seeking a single dedicated monitor holder. Confirm that your accessory’s weight and mounting thread fit the intended use.
Wide-Jaw Clamp with GoPro Adapter
SMALLRIG Super Clamp Mount, Ballhead Magic Arm and Adapter for Gopro
This SmallRig clamp combines a ball head, 1/4-inch-20 and 3/8-inch-16 threads, and a removable action camera adapter. Its jaw range supports rods from 14 mm to 60 mm, and surfaces up to 65 mm thick.
The stated maximum load is 3.5 kg. Anti-slip cushions and a hex-hole fastening point are intended to improve grip and reduce twisting.
It suits a broad range of mounting surfaces, from a tabletop edge to a tripod or handlebar. Before attaching a device, check the jaw dimensions and connection type; for motion, follow the product’s load guidance and secure the setup appropriately.
Best For: Clamping action cameras or light accessories to larger tubes, tables, or handlebars.
| Pros | Cons |
|---|---|
|
|
This is a versatile choice if you want one clamp for different surfaces and accessories. The 14–60 mm rod range and 65 mm surface limit are useful for checking fit, while the 3.5 kg rating provides a load ceiling.
The action camera adapter is removable, so the mount can serve devices that use standard threads as well. Compare it with smaller clamps if you mostly work at a desk and do not need the extra jaw range.
Height-Adjustable Desk Stand with C-Clamp
SMALLRIG Camera Mount C Stand, 15"-35" Adjustable Desk Clamp Table Tripod
The SmallRig 3488 is a tabletop stand with a C-clamp base, three extending pole sections, and a 1/4-inch ball head. Its height adjusts from 19 to 39 inches, and the clamp fits desks up to 1.85 inches thick.
The ball head rotates 360 degrees and tilts from -90 to +45 degrees. Its stated maximum load is 3 kg.
This is a useful alternative to a floor tripod for streaming, interviews, or desk-based shooting, especially when you want height above a work surface. Check desk thickness and the full height range against your placement needs.
Best For: Setting a camera, phone, or ring light above a desk for streaming or interviews.
| Pros | Cons |
|---|---|
|
|
Choose this desk stand if your camera or light needs an elevated, adjustable position for streaming, interviews, or close-up work. Its 19–39 inch height range and 360-degree ball head provide flexibility, while the C-clamp keeps the base on the desk rather than the floor.
Measure your desk edge and check your device’s weight before buying. For a rig that needs to travel between support points, a smaller clamp and arm are easier to reposition.
11-Inch Anti-Twist Magic Arm for Action Cameras
SMALLRIG 11" Magic Arm Clamp with 1/4"-20 Screw & Retractable Pins
The SmallRig 5311 pairs an 11-inch magic arm with a crab-shaped clamp and a 1/4-inch-20 screw with retractable locating pins. The clamp fits tubes, table edges, tripod legs, or stabilizer rings from 15 to 40 mm in diameter.
Its stated maximum payload is 1.5 kg. A single wingnut loosens the arm joints for positioning, then locks them together, while anti-slip pads help protect the clamped surface.
This longer arm works for flexible framing in vlogging or studio setups. Check both the clamp diameter and the accessory’s mounting points before purchase.
Best For: Positioning a lightweight camera or accessory on a tube, tripod leg, or table.
| Pros | Cons |
|---|---|
|
|
The 5311 is a fit for creators who want an 11-inch reach and a clamp that can attach to a tube or table edge. Its locating pins help with compatible action camera cages and other devices, but the 1.5 kg payload limit makes weight checks important.
Measure the mounting point and confirm your accessory’s thread and pin layout. If you need a shorter arm or wider jaw range, compare the other clamp kits before settling on this length.
Compact 7-Inch Anti-Twist Magic Arm
SMALLRIG 7 Inches Magic Arm Clamp, with 1/4 Screw & Anti-Deflection Pin
The SmallRig 5310 uses the same style of crab-shaped clamp and anti-twist 1/4-inch-20 connection as the longer 5311, with a 7-inch arm. Its clamp accommodates tubes, tables, tripod legs, or stabilizer rings with diameters from 15 to 40 mm.
The maximum payload is 1.5 kg. A wingnut loosens the joints for angle changes and tightens them together, and anti-slip pads help protect the clamped surface.
The shorter reach can keep a rig more compact when you do not need the 11-inch version’s added distance. Verify your mounting point and device fit first.
Best For: Mounting a lightweight action camera, monitor, light, or microphone close to a support point.
| Pros | Cons |
|---|---|
|
|
Choose the 5310 when a 7-inch reach is enough and you want to keep the accessory closer to its support. It shares the 1.5 kg payload and 15–40 mm clamp range with the 11-inch model, so the choice is mainly about placement distance.
Check the device’s connection points and the support diameter. If you need the arm to reach farther around a camera rig or desk setup, the 5311 offers more length.
Single 15mm Rod Block for Rig Expansion
SMALLRIG Super Lightweight 15mm Railblock, 15mm Rod Clamp with 1/4" Thread
This railblock is designed to attach two 15 mm rods to a compatible plate, cage, or handle. It provides 1/4-inch-20 threaded holes spaced 9 mm apart and includes short and long 1/4-inch screws to accommodate different mounting depths.
The aluminum block uses a spring ratchet wingnut to tighten the rods and reposition the lever in tight spaces. It is a specialized rig component rather than a general desk or camera-top mount.
Check that your rods measure 15 mm and that the mounting surface has compatible threaded holes before buying.
Best For: Adding a pair of 15mm rods to a compatible camera cage or plate.
| Pros | Cons |
|---|---|
|
|
Pick this railblock when you are expanding a cage or plate-based rig that uses 15 mm rods. The two rod openings and included screw lengths support a specific build task, while the 9 mm thread spacing gives you a detail to match against your mounting surface.
This is not a general-purpose clamp, so confirm that your cage or plate has compatible 1/4-inch-20 holes and that the rods are the right diameter before adding it to your setup.
One-Knob Magic Arm and Anti-Deflection Clamp Kit
SMALLRIG Magic Arm Clamp Kit, Camera Mount Friction Arm with Super Clamp
This kit combines a magic arm and super clamp with an integrated anti-deflection design at their connection point. A rotating triangular prism friction block helps the clamp grip flat surfaces such as a table edge, while the clamp can also hold round tubes.
The one-knob adjustment positions the accessory and arm, and the recommended load is 1.5 kg. The package includes an action camera mount, and the assembly uses aluminum alloy and stainless steel.
It suits compact camera and accessory setups that need a flexible angle. Check the surface shape and device weight before mounting.
Best For: Attaching a small camera, monitor, or light to a flat edge or round tube.
| Pros | Cons |
|---|---|
|
|
This kit is a sensible option for a small camera or accessory that needs angle adjustment on a desk edge or round support. Its friction block and integrated connection address two common fit questions, but the recommended 1.5 kg load means you should weigh the complete setup before mounting it.
Compare the clamp geometry with your surface and confirm the device can use the supplied action camera interface or a compatible thread. For longer reach, consider a 9.8-inch or 11-inch arm.
How to Choose Camera Mounts
How We Picked Camera Mounts
These camera mounts cover several distinct ways to position equipment: a clamp on a desk or tube, a shoe-mounted monitor holder, a 15 mm rod block, and a height-adjustable tabletop stand. We favored products with a clear connection method and fit details, such as jaw range, shoe type, thread size, rod diameter, or supported display size.
The included picks serve different setups rather than repeating the same mount in slightly different packaging. Compact clamps handle lighter accessories, longer magic arms extend a device away from its support, the cold-shoe holder targets field monitors, and the desk stand provides adjustable height for streaming or interviews.
Each option has a specific load or fit detail buyers can check against their camera rig.
Comparing Camera Mount Types
A super clamp or magic arm is useful when you need to attach gear to a surface without drilling. The SmallRig 1138 and the anti-deflection kits suit compact accessories, while the 9.8-inch kit and 5311 add reach.
The 5310 keeps the arm shorter for tighter positioning. Check the jaw range and payload together: a clamp that fits a tube still needs to support the complete camera and accessory setup.
For camera-top monitoring, the BSE2346 connects through a cold shoe and supports 5- and 7-inch monitors up to 1.2 kg. The 2059 ball heads also use cold shoes, but arrive as a two-pack and serve broader small-accessory placement.
The 3488 desk stand changes the equation with a clamp-on base and a 19–39 inch height range. It is useful when the camera needs to sit over a desk rather than directly on a camera cage.
The 942 railblock is different from a complete camera support. It provides a mounting point for two 15 mm rods on a compatible cage or plate.
Before buying a rod block, verify the rod diameter, cage threads, and available mounting space. For a more general camera mount, look at the clamp kits or desk stand instead.
| Product | Standout features | Best for |
|---|---|---|
| SmallRig 1138 Double Ball Head Super ClampCheck Price |
| Mounting a small camera, light, or microphone to a desk, rod, or frame. |
| SmallRig 2732 9.8-Inch Magic Arm Clamp KitCheck Price |
| Positioning a monitor, light, or microphone away from a clamp point. |
| SmallRig BSE2346 Cold-Shoe Monitor MountCheck Price |
| Attaching a 5- or 7-inch field monitor to a camera’s cold shoe. |
| SmallRig 2059 Mini Ball Head Mounts, 2-PackCheck Price |
| Adding two compact cold-shoe ball-head mounts to a camera setup. |
| SmallRig Super Clamp with Ballhead Magic ArmCheck Price |
| Clamping action cameras or light accessories to larger tubes, tables, or handlebars. |
| SmallRig 3488 Adjustable Desk Camera StandCheck Price |
| Setting a camera, phone, or ring light above a desk for streaming or interviews. |
| SmallRig 5311 11-Inch Magic Arm ClampCheck Price |
| Positioning a lightweight camera or accessory on a tube, tripod leg, or table. |
| SmallRig 5310 7-Inch Magic Arm ClampCheck Price |
| Mounting a lightweight action camera, monitor, light, or microphone close to a support point. |
| SmallRig 942 15mm RailblockCheck Price |
| Adding a pair of 15mm rods to a compatible camera cage or plate. |
| SmallRig Magic Arm Clamp Kit with Super ClampCheck Price |
| Attaching a small camera, monitor, or light to a flat edge or round tube. |
Check Clamp Fit and Reach
Measure the support before choosing a clamp. The 1138 attaches to rods, tubes, tables, frames, and tripods, while the 5310 and 5311 specify a 15–40 mm diameter range.
The wider-jaw super clamp with action camera adapter covers rods from 14–60 mm and surfaces up to 65 mm thick. The 9.8-inch kit opens from 15–54 mm.
These figures help distinguish a tabletop edge from a narrow tripod leg or larger handle.
Reach changes where the camera or accessory can sit. A longer arm can move a light or monitor around other equipment, but it also gives you more distance to manage.
The 7-inch arm works for closer placement; the 11-inch and 9.8-inch options provide more reach. Confirm that the surface can hold the clamp securely and keep the total load within the product’s stated limit.
Choosing a Camera Monitor Mount
A camera monitor mount should match both the display and the rig connection. The BSE2346 accepts a cold shoe at the support and a 1/4-inch-20 screw at the monitor.
Check that the display weighs no more than 1.2 kg and that your camera or cage has a suitable cold shoe. If your monitor mounts to a camera cage through a screw, confirm the thread and whether you need a locating pin or a particular cage interface.
A monitor holder with adjustable tilt and swivel helps position the screen for the shooting orientation, but the connection type determines whether it fits your setup. The selected cold-shoe support offers up to 140 degrees of tilt and 360-degree horizontal swivel.
For cages with 15 mm rods or ARRI locating points, inspect those interfaces separately; the railblock and excluded ARRI-style products serve more specialized builds.
Who Should Buy Which Camera Mount?
Choose the SmallRig 1138 or a magic arm clamp for a small camera, light, or microphone that needs flexible placement on a desk, tube, or frame. Consider the 5310 for a compact 7-inch reach and the 5311 or 9.8-inch kit when positioning farther from the clamp point matters.
Match the payload and jaw dimensions to the actual support and equipment.
Choose the BSE2346 for a 5- or 7-inch field monitor that attaches through a cold shoe, or the 3488 if you need a height-adjustable desk camera or light stand. The two 2059 ball heads suit buyers who can use both mounts.
Pick the 942 railblock only when your rig already uses 15 mm rods and a compatible plate or cage. Check the connection standard, support dimensions, and combined weight before ordering.